By using Mercury’s Mercury Thrust Washers and External Lock Washers, it will works fine. If you are using Yamaha thrust washers, it is best to cut off the wire cutter to prevent it from entering the seal. We spin a hub on our yamaha prop. When we had a yamaha, we then threw a Mercury and it worked fine.

Do mercury controls work on a yamaha?

Of course you can. We have a Merc / Yamaha (Merc-aha) 225 4 stroke on our port boat with a Merc controller/meter. Merc came up with an adapter for plugging the merc control/wiring into the Yamaha.

Are outboard motor props interchangeable?

Just like shoe size, the bore of the propeller is specific to the driveshaft on your boat. … Shafts are not interchangeableyou must use the correct size struts for your boat axle, otherwise the struts simply won’t fit.

Do Honda props fit a Yamaha?

As long as it clears, then you’re good to go.As for using Honda props on a Yamaha, if Spline matching, props fit snugly without skew, and then tighten the drive shaft with the spacer, good. As mentioned earlier, WOT is what determines what pitch is required.

Are the prop hubs interchangeable?

You can buy used propellers Interchangeable Hub Kits, or you can buy a prop with a press-fit rubber hub kit. The first time you use the interchangeable version, you’ll pay a little more, but later you can buy extra props for less without the hubs, as the hub kit can be moved to different props.

The Proper Way to Mount a Mercury Prop on a Yamaha Outboard

28 related questions found

Are Suzuki and Yamaha props interchangeable?

You’ll be fine running a Yamaha prop on a Suzuki, the difference is the outer diameter size of the propeller barrel.Yamaha outboards have one narrower than gearbox Suzuki, if you have a Yamaha strut on your Suzuki, then you should leave about 1/4 inch of clearance between the ID of the gear and the OD of the strut barrel.

Can you fix a spinning prop?

Propeller rotation means that the propeller hub rotates within the propeller. … repairing a spinning propeller requires the assistance of A boat propeller repair shop Press the old hub out of the propeller and the new hub into the propeller.

Will Mercury props be suitable for troops?

Yes, which will fit the motor. This prop is for the Force made by the Force (that’s what you have), not the Force made by Mercury.

Are tohatsu props suitable for Mercury?

FYI Mercury and Tohatsu props are interchangeable New 4 strokes!

Are OMC props suitable for Mercury?

Since OMC/BRP motors have less propeller shaft splines than motors from other manufacturers, You can install OMC propellers on Mercury, but not vice versa.

3 or 4 which is better?

3 or 4?One 3-blade propellers typically provide top speed performance And the 4-blade propeller provides maximum thrust and smooth cruise operation. However, the four blades each have some features of their own. They usually provide more lift at the stern, which will help accelerate the hull, especially if the stern is heavy.

Are Yamaha and Tohatsu props interchangeable?

They are all splined the same, possibly a spline length issue. Hubs may be too short or too long to be interchangeable.

What pitching prop can make my boat go faster?

One Bass prop It’s like a low gear in a car or bike – you’ll accelerate quickly, but top speed will suffer. A propeller that is too pitched may provide a higher top speed as the propeller will move further forward with each revolution, but the acceleration may be poor and the boat will struggle to get on the plane.

Are outboard controls universal?

Generally speaking, all Other engines and controllers use « universal » Type 3300/33C control cables. Universal cables have 10-32 threaded ends and usually require additional hardware to connect to the engine and controls.

Are all mercury controls the same?

very common. It all depends on how much you want to spend. New Gen 2 hardware should all be backward compatible with your engine. I personally prefer the Teleflex Extreme cables to the Mercury standard cables, but they do cost more (usually).

What spacing props should I use?

Each inch of pitch size will change the RPM by 150-200 RPM.Target For the midpoint or higher of the recommended operating range. Remember that high altitude reduces engine power, so choose a lower pitch to achieve the same rpm as sea level. Engine height also affects propeller performance.

How do I know what size props I need?

propeller size a set of numbers, such as 13×17 or 19×23 are usually marked on the propeller. The first number is the diameter (the width of the blade circle) and the second number is the pitch (the theoretical travel distance per revolution of the inclined blade). Two other design features include rakes and cups.

Are Suzuki props right for Johnson?

Yes, Suzuki fits OMC….don’t use susuki shims on OMC and vice versa.

Is the force outside of Mercury?

Our Force outboard motor parts are Genuine OEM parts made by Mercury Marine.Force was acquired by Brunswick Corporation (owner of Mercury) in 1986, and since then Mercury has been producing OEM Force marine parts to the same standards and specifications as the original Force factory.

How much does it cost to fix a spinning prop?

Prop hub replacement cost is usually anywhere $50 to $100, depending on your engine and where you take it. The retaining struts need to be pressed out of the old hub and replaced with a new one. You can do this process yourself if you have the right tools.

How do I know my boat prop is broken?

8 Clear Signs It’s Time to Replace Your Boat Propeller

1. It has too many tones. …
2. It doesn’t have enough pitch. …
3. It’s a compromise propeller. …
4. You damaged it in the water. …
5. It is made of aluminum. …
6. You want to go faster. …
7. You are losing gas. …
8. This is not the correct diameter.

What causes the prop blowout?

blowouts occur for some reason Air/water mixture in the propeller area Disturbed enough, the propeller can’t continue to work in « clean » water and tries to work through a very soft or light mixture (or a relative vacuum).

Are Mercruiser props suitable for Volvo?

well-known member. Chet, You can’t mix and match mercruiser props, with Volvo Penta props, the splines will never match. And the suggestion to convert your outboard to twin props, you can’t push twin props with 5.0, it just doesn’t have the ability to push twin props and you’ll burn out the engine.

What is the difference between 19 and 21 pitch lanes?

Propeller pitch is often referred to as « propeller pitch » and is essentially the distance the propeller travels through a soft solid in a single turn. …so in this case, « 21 pitch struts » will move forward 21 inches in one revolutionand the 19-pitch strut will move forward 19 inches in one revolution.